PPCT Scream’N Continuity Tester

Probe tip current:           10 mA. Max.

Open circuit voltage:        3.0 V

Volume:                           100 dB @ 1ft. Max.

Low tone:                         < 10 Ohms

High tone:                        > 10 Ohms <1K Ohms

No tone:                           > 1 K Ohm

Batteries:                         (2) AA

Voltage detection:            6-50 VDC

Banana Jacks ;                4mm, shrouded, gold plated

Storage temperature:       -40°C (-40°F) to 70°C (158°F)

Operating temperature     -20°C (-4°F) to 60°C (140°F)

PPSK Solder Torch

Watt:                     120

BTU:                     500

Max Temp:           2500°F (torch)

Max Temp:           950°F (soldering)

PPMT Micro Torch

Watt:                     120

BTU:                     580

Max Temp:           2500°F (torch)

Max Temp:           950°F (soldering)

Power Probe III

Maximum Voltage on Probe Tip: ± 200 Volts Relative to the Negative Battery Clip

Probe tip resistance to ground 130KΩ   Computer Safe: 0.1mA floating tip

(warning: do not press power switch while connected to computer circuits with PP1,2 or 3)

Power Probe Mode (Mode 1)

DC Voltage Measurement: 0 to 70 Volts (in 1/10th increments)

AC Voltage Measurement: 0 to 70 Volts Peak to Peak

(See Peak to Peak & Threshold Setting Mode 5)

Square Wave Input Response: 15 Hz to over 500KHz

Sine Wave Input Response:     35 Hz to over 250KHz

Continuity to Ground:      Greater than 20K Ohms - Display is Blank

Less than 20K Ohms:       Display reads 0.0

Less than 2K Ohms:         Display reads 0.0 and Green Led is On

Min (Mode 2) & Max (Mode 3)

Voltage Measurement:     0 to 70 Volts

Single Event Capture:      Less than 200 Micro Second Pulse Width

Repetitive Events:            Less than 1 Micro Second Pulse Width

Peak to Peak Mode (Mode 4)

0 to 70 Volts P-P

Square Wave Input Response:  4 Hz to over 500KHz

Sine Wave Input Response:      4 Hz to over 250KHz

Peak to Peak Mode Threshold Setting (Mode 5)

0.2, 0.5, 1, 2, 5, 10 & 50     When the Peak to Peak Voltage on

the Probe Tip exceeds this threshold then the display is

Peak to Peak AC rather than DC.

 

Storage temperature:       -40°C (-40°F) to 70°C (158°F)

Operating temperature     -20°C (-4°F) to 60°C (140°F)

Circuit Breaker

8 amp thermal response - manual reset   8 amp=No trip  10 amps=20 min.  15 amps=6 sec.

                                                                  25 amps=2 sec.   Short circuit=0.3 sec.

ECT2000

Voltage range:                  12-42v

Transmitter signal:            8v  4kHz

Circuit Signal Max:           100 mA

Batteries:                          (2) AAA

Banana Jacks ;                 4mm, shrouded, gold plated

Storage temperature:       -40°C (-40°F) to 70°C (158°F)

Operating temperature     -20°C (-4°F) to 60°C (140°F)

Power Probe I*

Voltage range:             6-24v

Probe tip current:      10 mA. (12v system)

Open circuit voltage:    6.0v (12v system)

Power Probe II*

Voltage range:             12-24v

Probe tip current:       10 mA. (12v system)

Open circuit voltage:    6.0v (12v system)

*Storage temp:             -40°C (-40°F) to 70°C (158°F)

*Operating temp:          -20°C (-4°F) to 60°C (140°F)